Patching

I have applied orange gelcoat to a few places on the hull and also to some of the recessed deck fittings. A piece of plastic pipe is now held in place for a knee tube using a length of glass tape and some clear gelcoat, which also serves for patching over the holes for the deck elastics. The front hatch flange has been fixed using some more short strips of glass tape and the clear gelcoat.

In retrospect, I should have used some clingfilm over the front hatch repair to allow me to press it into place neatly. There are a couple of places where the ends of a strip of tape is not bonded to the boat properly. My feeble excuse is that it's a bit tricky working through the tiny hatch.

Using washing powder to clean the brushes does seem to work.

Keel strip - final layer

Thanks to my mistake last night, the keel strip will now have three layers. I hand to sand down the first attempt at a layer of coloured gelcoat; this was to remove the lumps but also to remove the surface so that the new layer would stick.

I had to re-apply masking tape along the sides of the keel strip and then apply a new batch (100g + 2ml catalyst) of coloured gelcoat. There was a bit left over, so I did a bit of purely cosmetic repair to the black gelcoat along the seams.

I used a brush similar to the one that I had to throw away last night. I'm hopeful that this brush has come clean using washing powder and water.

I let the gelcoat start to set while I washed the brush and had some breakfast. I then removed the masking tape. It looks good and I'm keen to get back to it this evening and check it over properly.

My plan for this evening is to apply a small amount of orange gelcoat to a few places on the hull. If I get time then I may also do the first layer on the knee tube (including patching over the holes for the deck elastics) and the front hatch. I can then do the final layer on the knee tube, either this evening (unlikely) or tomorrow morning. This should be all of the work that needs to be done with the boat upside down, so I should be able to start tidying up the deck with some more orange gelcoat tomorrow evening. I'll probably be putting back the front hatch and re-fitting my decklines on Friday evening as I get ready to go off paddling for the weekend!

The deck elastics will ultimately be fitted using some sort of screw fitting through the deck; I may have to do without for a while until I can find some suitable parts. I've also got to buy a footpump but I'm currently well within my budget, having spent about £80 so far.

Keel strip - Problems with gelcoat

The black gelcoat decided to set rather quickly. This might be because I was holding the plastic pot in my warm hand or because the proportions were slightly wrong. This meant that the last bit of the keel strip went a bit lumpy.

In retrospect, I should have stopped as soon as the gelcoat started to go off. I could then have mixed up a fresh batch. However, I tried to save myself some time and paid the consequences.

It was nice to see that peeling off the masking tape gave a clean edge to the keel strip.

I used 150g of gelcoat, with 3ml of catalyst. Most of this went onto the boat although I probably wasted over 25g.

Keel strip - first layer

I have taken an approach that is a combination of the descriptions from several websites and some advice from P&H. The first layer of the keel strip is to be made of glass tape embedded in clear polyester gelcoat, with a second layer that is made of coloured gelcoat that is waxed to allow it to set in air.

Masking tape is used to give a neat finish and to make the job easier. The tape is cheap when compared with the other repair materials and the time that the repairs take.

The first line of masking tape is a guide for the other lines. It will be removed before the resin work starts. It is done with masking tape that is the same width as the glass tape that is to be used for the keel strip. I used two-inch tape.
The second and third lines of two-inch masking tape go either side of the first, with a gap of a good quarter of an inch. The gap could be made narrower but it would depend on the confidence of the person doing the work!
The fourth and fifth lines of masking tape can use a narrower tape. I used one-inch wide tape. These lines of tape go mostly on top of the second and third lines, along the edge that is towards the centre. This closes half of the gap between the first line of tape and the second/third line.
Once I was happy that everything looked right, I removed the first line of tape. This leaves an exposed area for fitting the keelstrip that is about 2.25 inches wide.
I painted clear gelcoat along the exposed area and then used some glass scraps mixed with gelcoat to fill a couple of holes in the keel. A length of glass tape was laid out along the whole of the keel. I did the stern with a separate shorter strip. The glass tape was then wetted out using more gelcoat on a small brush. I needed about 200g of gelcoat, using 4ml of catalyst that I measured with a syringe. I put a second layer of tape along the sections at the front and back that take most wear and wetted this out throughly.
Once the gelcoat started to set, I removed the one-inch masking tape. (Pulling the tape towards the centre of the boat kept the resin from spreading to the area that I uncovered.) This leaves a gap of about an eighth of an inch between the remaining masking tape and the new keelstrip. The whole of this area will be painted with waxed, coloured gelcoat this evening. The gap serves two purposes: it ensures that all of the unwaxed gelcoat is covered and it tapers the repair a little to give a nicer finish.

I'll be left with a keelstrip that is 2.5 inches wide and has added about 0.4kg to the boat, although stripping off the old keelstrip will have taken off a similar mass. The new keelstrip is a bit bigger than might be ideal but should protect the boat nicely.

Hull repairs

I had removed some external repairs whilst getting rid of the old keelstrip. There were two places that needed some repair work and I decided that it would be neater to do it internally, reaching through the hatches. This made it a bit tricky to get a neat finish, so I was glad that the repairs won't be visible to anyone else!
I did the repairs with some woven glass and polyester gelcoat (with styrene wax to allow it to set in air - "Resin B" from Scott-Bader). This may be cheating a bit but I had the materials to hand and it gave me a quick and easy repair.

Stripping and sanding

I took advantage of some nice weather to spend an afternoon in the garden with my boat, a chisel and some sandpaper. The bonus was that I could work on the boat while still looking after the kids.

I removed the old keelstrip and investigated the leak in the front compartment. Some cleaning up around the front hatch revealed that the flange is broken and is detached from the deck at several points.
The chisel got blunted pretty quickly. The grindstone got some use.

Got the materials - just need the time

The materials that I ordered from P&H arrived as promised. I just need to find some time to start working on the boat. Trouble is that it's more fun to just go out and paddle it!